Poulan-pro PP4000C User Manual download pdf (Page 5)

5

Locking/Release

Button in Primary Hole

HANDLEBAR ASSEMBLY

DANGER:RISK OF CUT. To avoid se-

rious injury, the barrier portion of the handle-

bar must be installed as shown on the upper

shaft of the powerhead to provide a barrier be-

tween operator and the spinning blade. Attach

handlebar mounting bracket above arrow on

safety warning decal on the upper shaft (pow-

erhead end of unit). Ensure handlebar is posi-

tioned on mounting bracket at the end of the

arrow on the handlebar decal.

NOTE: Two mounting brackets are included

with this attachment. Both brackets are provided

to adapt this attachment for use with power-

heads that have either a 1″ (2.5 cm) diame ter or

a7/8″ (2.2 cm) diameter upper shaft. The cor-

rect bracket must be used to ensure that the

handlebar is mounted securely to the upper

shaft before use.

Screw

Mounting

Bracket

Handlebar

Bracket Cover

1. Place the mounting bracket over the up-

per shaft above the arrow on the safety

label. Be sure to use the correct mount-

ing bracket for either the 1″ (2.5 cm) or

7/8″ (2.2 cm) diameter upper shaft.

2. Position one of the bracket covers under

the upper shaft and align the mounting

bracket an d the bra cket cover screw hol e s.

Insert two screws into the screw holes.

3. Secure the mounting bracket by tighten-

ing the screws with the hex wrench.

4. Locate the decal on the handlebar. This

decal includes an arrow. Position the

handlebar with the mounting bracket at

the end of the arrow.

5. Position the second bracket cover over

the handlebar . Align the mounting brack-

et and the bracket cover screw holes.

Again make sure the handlebar is at the

end of the arrow.

6. Insert two screws and hand tighten only.

Be sure the handlebar is installed cor-

rectly; then, tighten each screw securely

with the hex wrench.

SHOULDER STRAP ASSEMBLY

WARNING: Proper shoulder strap

and handlebar adjustments must be made

with the engine completely stopped before us-

ing unit. The sho ulder strap cla mp must be

installed as shown above the handlebar on the

upper shaft (powerhead end of unit).

NOTE: The lower shoulder strap clamp has

two spacer tabs attached. These tabs are pro-

vided to adapt this attachment for use with

powerheads that have a 1″ diameter upper

shaft (the shoulder strap clamp will not tighten

down securely on the 1″ diameter upper shaft

without using these spacer tabs). The tabs

must be broken off completely before use and

placed over the screw holes on the lower

shoulder strap clamp. These tabs are not

needed for powerheads with a 7/8″ upper

shaft.

Spacer Tabs

LOWER SHOULDER STRAP

CLAMP

Spacer Tabs

positioned for use

on 1″ diameter

upper shaft

1. Place the upper shoulder strap clamp

over the upper shaft above the handlebar.

2. Position the lower shoulder strap clamp

under the upper shaft and align the upper

and lower clamp screw holes (use

spacer tabs between upper and lower

clamps if necessary to secure clamp, i.e.

for 1″ diameter upper shaft).

Upper Shoulder

Strap Clamp

Screws

Lower Shoulder

Strap Clamp

POWERHEAD

END

ATTACHMENT

END

3. Insert two screws into the screw holes.

4. Secure shoulder strap clamp by tighten-

ing screws with the hex wrench.

5. Insert your right arm and head through

the shoulder strap and allow it to rest on

your left shoulder . Make sure the danger

sign is on your back and the hook is to the

right side of your waist.

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments