Poulan-pro PP291E30 SNOW THROWER User Manual

OWNER'S MANUALMODEL NUMBER:PP291E30SNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the O

10TO CONTROL SNOW DISCHARGE (See Fig. 13)WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma-

11OPERATIONTO THROW SNOW (See Fig. 14)The auger rotation is controlled by the auger control lever located on the right side handle.• Squeeze auger co

12BEFORE STARTING THE ENGINECHECK ENGINE OIL LEVEL (See Fig. 19)The engine on your snow thrower has been shipped, from the factory, already filled wit

13OPERATIONTO START ENGINE • Be sure fuel shut-off valve is in the “OPEN” position.Your snow thrower engine is equipped with both a 120 Volt A.C. ele

14 SAE 5W-30 Motor Oil See “ENGINE” inMaintenance section General Purpose GreaseGENERAL REC OM MEN DA TIONSThe warranty on this snow thrower d

15MAINTENANCEAUGER GEAR CASE• The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention

16SERVICE AND ADJUSTMENTSBELT COVER SCREWSFRAMEFIG. 21TO REMOVE BELT COVER (See Fig. 21)1. Remove the two (2) screws securing belt cover to frame.2.

17SERVICE AND ADJUSTMENTS8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.HINT: Insert a 3/8"

18SERVICE AND ADJUSTMENTSENGINESee engine manual.CARBURETORYour carburetor is not adjustable. Engine performance should not be affected at altitudes u

19STORAGEImmediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never store t

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

20TROUBLESHOOTINGDoes not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2.

21REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

22REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

23REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

24REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

25REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

26REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.

27REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.

28REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTAN

29REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTAN

3CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u -fac tured to give best possible dependability an

30REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTAN

31REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTAN

32REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT:

33REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT:

34REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT:

35REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)CHASSIS / ENGINE / PULLEYSNOTE: All component dimensions given in U.S. inches. 1 inc

36REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)CHASSIS / ENGINE / PULLEYSNOTE: All component dimensions given in U.S. inches. 1 inc

37REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)WHEELSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT

38REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)BAG OF PARTSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMP

39NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

4PARTS PACKED SEPARATELY IN CARTON(3) RETAINER SPRINGS (169675)(1) WASHER 3/8(19131316)(1) LOCKNUT 3/8(73800600)(2) SAFTEY IGNITION KEY(422663)(1) MU

LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and w

5Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual w

6ASSEMBLY / PRE-OPERATIONINSTALL TRACTION DRIVE CONTROL ROD(See Figs. 3 and 4)The traction drive control rod is installed on the snow thrower.1. Remo

7ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins

8OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

9OPERATIONDrive speed control lever - used to select forward or reverse motion and speed of snow thrower.Traction drive control lever - used to engage