OWNER'S MANUALMODEL NUMBER:PP265E27SNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the O
10OPERATIONTO USE FUEL SHUT-OFF VALVE (See Fig. 11)The fuel shut-off valve is located beneath the fuel tank on the engine. Always op er ate the snow t
11OPERATIONTO THROW SNOW (See Fig. 15)The auger rotation is controlled by the auger control lever located on the right side handle.• Squeeze auger co
12OPERATIONTO ADJUST SKID PLATES (See Fig. 18)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are locate
13OPERATIONCOLD START - ELECTRIC STARTER1. Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn th
14MAINTENANCEGENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or neglige
15MAINTENANCEAUGER GEAR CASE• The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention
16SERVICE AND ADJUSTMENTSTO REMOVE BELT COVER (See Fig. 21)1. Remove the two (2) screws securing belt cover to frame.2. Remove belt cover.• Replace
17SERVICE AND ADJUSTMENTS8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.HINT: Insert a 3/8"
18SERVICE AND ADJUSTMENTSTO REMOVE WHEELS (See Fig. 23)• Remove the klik pin and remove wheel from axle.IMPORTANT: When installing wheel, be sure to
19STORAGEImmediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never
2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure
20TROUBLESHOOTINGDoes not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2.
21NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
22NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
23REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002800)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inc
2412344301.11.001-AKEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use onl
255715163*11*142461689*12*1310601.09.015-AKEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25
26NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
27NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
28NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
29NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
3MAINTENANCE ... 14-15SERVICE AND AD JUST MENTS ... 16-18STORAGE ...
30NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
31NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
32NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
33REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002800)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPO
34NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
35NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
36KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm
37KEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONREPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002800)BA
38KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm
39REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002800)265CC POULAN PRO ENGINE-MODEL NUMBER 4287571 429944 CRANK CASE 12 429945 CRANKS
4PARTS PACKED SEPARATELY IN CARTON(3) RETAINER SPRINGS (169675)(1) WASHER 3/8(19131316)(1) LOCKNUT 3/8(73800600)SAFTEY IGNITION KEY (S)(429955)(1) MU
401. FEDERAL EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSThe United States Environmental Protection Agency(EPA), together w
41WARRANTYII. EMISSION CONTROL SYSTEM WARRANTYEmission Control System Warranty (ECS Warranty) for 2009 and later model engines:(a) Applicability: This
42(9) Unapproved, add-on, modified, counterfeit and/or “grey market” parts may not be used to modify or repair a Husqvarna Consumer Outdoor Products N
43LIMITED WARRANTYHOP (The "Manufacturer") warrants to the original consumer purchaser that this product as manufactured is free from defect
5ASSEMBLY / PRE-OPERATIONSPEEDCONTROL RODHANDLE KNOBLOWER HANDLEPLASTIC TIEUPPER HANDLEFIG. 1NOTE: The multi-wrench may be used for assembly of the ch
6ASSEMBLY / PRE-OPERATIONAUGERCONTROL LEVERAUGER CONTROL RODAUGERCONTROL BRACKETRETAINER SPRINGFIG. 6INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See
7ASSEMBLY / PRE-OPERATIONCHECK TIRE PRESSUREThe tires on your snow thrower were overinflated at the fac-tory for shipping purposes. Correct and equal
8OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with
9MEETS A.N.S.I. SAFETY REQUIREMENTSOur snow throwers conform to the standards of the American National Standards Institute.OPERATIONFIG. 10NOTE: ITEMS
Comments to this Manuals